Exceed RC 3-Channel J3 Piper Cub EP Electric RC Airplane 100% Ready-to-Fly 3388_SDJ3
  • Exceed RC 3-Channel J3 Piper Cub EP Electric RC Airplane 100% Ready-to-Fly 3388_SDJ3
Item Code: 3388_SDJ3

Out of stock


RC J3 Piper Cub


Exceed RC's SD J3 Grasshopper Scale RC Plane 1:10 SCALE READY TO FLY Electric Powered RC Airplane, Brand New! Ready to fly RC with amazing performance. Complete with 3 channel C&F RC, 9 gram micro servos, rechargeable battery and charger installed. Even the pushrods and control surface horns are fitted! Factory built. Just takes minutes to assemble. You can even remove the RC and use it in other models! What a great investment in fun!!


Piper Cub J3 Beginners Guide Part 1
Piper Cub J3 Beginners Guide Part 2

RC J3 Piper Cub

RC J3 Piper Cub

The J3 CUB 3 Channel has successfully trained thousands of newbie radio controlled pilots worldwide. You'll be flying within minutes of receiving this fully built airplane enjoying over 12 minute flight times on a single charge thanks to our new improved NiMH battery and ball bearing gear drive system. Equipped with a powerful speed electric motor, which starts with a push of a button, the J3 CUB is capable of take-offs from the ground with its huge powerful motor and wide wingspan.

RC J3 Piper Cub

  • Battery Operated 380 Motor Plane
  • Ready to Fly, assembly can be done in 10 mins
  • Digital Proportional Speed Controller
  • Slow Speed Flying Capable, Good for Beginner
  • Shock Resistant Reinforced Foam Fuselage and Strong Wings
  • 2 X 18g micro servo for Rudder and Elevator Control
  • R/C Set included, Complete 3 Channel Control including
    • Complete Left/Right Control by Rudder
    • Complete Elevator Control
    • Digital Proportional Motor Speed Control Knob
  • Superb Quality--Simply The Best RTF Plane you can find
  • Up to 300Maltitude, over 15 mins flight time
  • Powered by 8.4V NIMH re-chargeable battery (110v adaptor included)
  • Can Fly as a Glider (without Motor Power)
  • Brand NEW
  • All tools required are included for you
  • Assembly take less than 20mins
  • Best Looking Plane on the market

RC J3 Piper Cub

Data Sheet:

  • Ready to fly (RTF) with battery charger and RC!
  • Includes REAL RC equipment which can be used in other models!
  • Wing span - 37.5 inches (95.5cm)
  • Length - 28.8 inches (73cm)
  • Wing area - 13.7dm2

RC J3 Piper Cub

Assembly is a snap! With no tools required, you can be up and flying within minutes of opening the box!

Highlighted features for this airplane

RC J3 Piper Cub Transmitter

3 Channel Radio Controller features:

  • Left/Right Control
  • Elevator Control
  • Digital Progressive Motor Speed Control Knob

Newest design Full 3 Channel capability with a variable speed throttle control

These servos are "Designed to work with almost all Radio Control Systems" Compatiable w/: FUTABA, JR, HITEC, AIRTRONICS, GWS, SANWA & AASHAI Radio Systems

This Receiver Is Designed To Handle Hitec, Futaba, Airtronics, JR on 27MHz. Whole-digital modulational circuitry, with the function of signal discrimination, is sensitive to receive the signal and strong to resist interference.

Micro high frequency electronic speed control with the battery eliminator circuitry (BEC). It is designed for electric motors up to a speed 600 in size. It will handle up to an 8 cell battery pack and is rated for a maximum of 22 amps continous current.

Ni-MH Battery
Uses one rechargeable NiMH battery pack (included) and an automatic DC peak battery charger.

Novice Advanced Beginners Competent Proficient Expert